Chitongda YL-007M2 Manual de usuario

MOBILE CALL GSM Alarm System User’s Manual Profile For a better understanding of this product, please read this user manual thoroughly before us

10 The remote controller can’t control the main unit after it’s deleted. In setup state, use keypad to input [21], then input the remote controller

11 1) Change Operation Password Operation password is the password used to disarm or remote control. In setup status, use keypad to input

12 digits [EE] of the minute, the two digits [FF] of the second, and finally enter [#] to confirm. You will hear a long beep and a voice

13 Operating method: [XX][AA][BB][#] XX indicates: the address code 36, 37, 38 of the timely disarming AA indicates: the hour of the setting time

14 LCD display: 13. Wireless Siren Coding Encryption Only the panel with built-in transmitter has this function. The signal used to code with

15 In setup state, input the command: 45 + [XX] + # XX indicates: the delay time of alarm; XX= 01-99: 1 sec to 99 sec Note: The setting

16 18. SMS Receiving Number Setting SMS Receiving number means when system is alarming, it will only send SMS to this mobile number. Yo

17 keyboard operation. 21. Defense Zone Programming If you want to change the alarm attribute of defense zone, such as turn off the siren when

18 defense zone number [01~99], then choose [Home Arm], and then choose whether alarm [0/1] button, and finally press [#] to confirm. The m

19 24. Arm/ Disarm Siren Sound Setting After you activate this function, when you arm the system, the external siren will sound one short beep; a

2 Contents Function Introduction Alarm Host Diagram Door Sensor Wireless PIR Detector Functions Settings I

20 confirm; voice prompts: setting completed, please enter instruction. Operating method:【83】【A】【#】 A indicates: [1]: activate voice prompt for ar

21 Users can use remote controller to set system as Out Arm, Home Arm, Emergency Alarm, Real-time Disarm and etc.  Out Arm: Press button 

22 After the setting, the host makes a "Di" sound, ARM LED is on and you will receive a SMS: System armed. 5. Disarm It means to stop th

23 If you answer the call, you will hear the pre-record voice. You can set system via your telephone or mobile phone keypad. If you hang-up d

24 In disarm status, you can use the main unit to make any call just like a land-line telephone. Dial telephone number on keypad, press [ ] button,

25 NO9 Zone: 19 Time: 11-06-25 11:45 (It indicates the first record: wireless zone 19 alarm time) 11. GSM Signal Checking Before installing the

26 [Technical Parameters] List 1: Input Voltage DC12V/1A Standby Current <55mA Alarming Current <450mA Wireless Frequency 315/433MHz, PT22

27 Siren sound time 180 sec. Home Appliance Optional [Components List] Main panel 1 pc, Remote controller

28  Keep the alarm system dry. Rain, humidity and various fluids or moisture all will corrupt the electronic circuit.  Do not use or place the a

29 other people remote control the system illegally.  Since the alarm system is continuously in operation or standby mode, the supply ada

3 Components List Care and Maintenance [Function Instruction] 1. 7 wired and 99 wireless defense zones; 2. LCD screen with time

30 Optional sensors/detectors are packed separately. You can choose according to your specific requirements.

31 Operation Commands Function Description Remarks [Program Password] + [#] Enter settings Default password: 8888 [*] + [#] Exit settings [20]+[1

32 [AA]: hour [BB]: minute [39] + [0/1] + [#] Timing Control: turn on/ off the function of timely arm/disarm 0: OFF 1: ON [41] + [

33 [1]SOS Alarm; [2] Fire Alarm; [3]Gas Leak Alarm; [4]Door Alarm; [5]Hall Alarm; [6]Window Alarm; [7]Balcony Alarm; [8]Boundary Alarm D:

34 [Dial telephone number] +[ ] System Dialing Function [95175308246] + [#] Factory Reset Use with caution [operation password] + [1] Arm by SMS D

4 concrete wall or fire door, etc. Alarm Panel front schematic diagram: Alarm Panel back schematic diagram: Wired terminal block:

5 1 LB- Negative of speaker (black cable) 2 LB+ Positive of speaker (red cable) 3 GND Ground 4 Z1 Wired sensor 1: support both NO and NC 5 GND Grou

6 3. Please pay attention to the siren connection. Do not mix the two cables together when connecting. Otherwise, it will damage the transistor in

7  Magnet should be near to the side of transmitter with indicator. The two should align with each other and the distance should not exce

8 Choose the most suitable installation place and angle according to actual situation and taking the following installation diagram as referen

9 LCD display: 3. Exit Settings Press [*] and [#] buttons, the main unit emits a long beep and exits settings. The [SET] indicator